[產品] Raspberry Pi Compute module 3+ / 8GB (CM3+/8GB)

Raspberry Pi Compute Module 3 + 8GB eMMC -  CM3+/8GB

compute-module-3-plus-front

The Compute Module 3+ (CM3+) is a Raspberry Pi 3 Model B+ in a flexible form fator, intended for industrial applications.

《特色》

The CM3+/8GB Compute Module contains the guts of a Raspberry Pi 3 Model B+ (the BCM2837 processor and 1GB RAM) as well as an 8GB eMMC Flash device (which is the equivalent of the SD card in the Pi).

  • Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.2GHz
  • 1GB LPDDR2 SDRAM
  • 8GB eMMC Flash memory

This is all integrated onto a small (67.6mm × 31mm) board that fits into a standard DDR2 SODIMM connector. The Flash memory is connected directly to the processor on the board, but the remaining processor interfaces are available to the user via the connector pins. You get the full flexibility of the BCM2837 SoC (which means that many more GPIOs and interfaces are available than with a standard Raspberry Pi), and designing the Module into a custom system should be relatively straightforward because we’ve put all the tricky bits onto the Module itself.

To help you get started designing a PCB to use the Module, we provide an open-source breakout board, which is supplied with both a CM3+/32GB and a CM3+/Lite in an affordable development kit.
購買CM3+/8GB $1260 


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

※請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi Compute module 3 (CM3)

Raspberry Pi Compute module 3

RPI-COMPUTE3-2in1

The Raspberry Pi Compute Module 3 (CM3) and Compute Module 3 Lite (CM3L) are DDR2-SODIMM-mechanically-compatible System on Modules (SoMs) containing processor, memory, eMMC Flash (CM3 only) and supporting power circuitry. These modules allow a designer to leverage the Raspberry Pi hardware and software stack in their own custom systems and form factors. In addition the modules have extra IO interfaces over and above what is available on the Raspberry Pi model A/B boards, providing more options for the designer.

《特色》

The Compute Module 3 contains the following components contained within a 200 pin SODIMM design:

  • Broadcom BCM2837 processor
  • 1Gbyte LPDDR2 RAM
  • 4Gbytes eMMC Flash
  • 35u hard gold plated IO Pins

單買CM3 $1470 



Raspberry Pi Compute module 3 Lite

RPI-COMPUTE3-LT-2in1

《特色》

The Compute Module 3 Lite product is the same as the Compute Module 3 except the eMMC Flash is not fitted, and the SD/eMMC interface pins are available for the user to connect their own SD/eMMC device The Compute Module 3 Lite contains the following components contained within a 200 pin SODIMM design:

  • Broadcom BCM2837 processor
  • 1Gbyte LPDDR2 RAM
  • 35u hard gold plated IO Pins

(N.B. when operating with the IO Board, an SD card with a suitable image must be connected to the IO board for the system to work)
單買CM3 Lite $1260 



Raspberry Pi 3 Compute Module I/O

Raspberry-Pi-3-compute-module-IO-2in1

《特色》

This is the main development kit IO board into which the Compute Module SODIMM board is connected. It also contains all of the necessary interface ports to allow an engineer to design and test their own prototype application.

The IO board contains the following interfaces:

  • Multiple GPIO interfaces on 2 60 way 0.1” Headers
  • 1 x Micro USB connector type B – USB Slave
  • 1 x USB connector type A – USB Host
  • 2 x CSI ports for camera boards
  • 2 x DSI ports for display boards
  • Full size HDMI port
  • Micro USB power connector
  • Micro SD connector

單買Compute Module I/O Board $5150



Raspberry Pi Compute Module 3 Development Kit

RPI-COMPUTE3-KIT-4in1

《特色》

The Raspberry Pi Compute Module 3 Development Kit contains the following components:

  • 1 x Raspberry Pi Compute Module 3
  • 1 x Raspberry Pi Compute Module 3 Lite
  • 1 x Raspberry Pi Compute Module IO Board
  • 1 x Raspberry Pi Compute Module IO Board Camera Display Adaptor
  • 1 x 5v 2.5A Power Supply
  • 1 x USB A to micro B cable
  • 4 x Jumper wires

《下載》

The schematics and board design files for the Compute Module IO board have been published by the Raspberry Pi Foundation and detail the interconnection between the SODIMM socket and the interfaces on the IO board. These can be found at: https://www.raspberrypi.org/documentation/hardware/computemodule/

購買全套CM3 Development Kit $8200 


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。