[產品] Raspberry Pi 樹莓派 UPS 鋰電池擴充板 USB 電源供應模組 行動電源 雙USB輸出

SONY DSC

專為樹莓派設計的 UPS 鋰電池擴充板,雙USB輸出,可當行動電源使用,或用於其他USB供電等設備。

《特色》

  • 適用於B+以後版本樹莓派,Raspberry Pi A+B+2B3B and 3B+
  • 可邊充邊放,停止充電時不影響放電
  • 雙模供電:行動電源模式及UPS供電模式
    • 行動電源模式,採鋰電池供電,最高可達 5.1V/2.5A。
    • UPS供電模式,microUSB input 接上5V/2A電源,output 最高可達 5.1A/3A
  • 4+2LED 顯示充電、放電及電池狀態
  • 保護功能:output 有一個self-recovery fuse保險絲,防止樹莓派因外部短路而燒毀
  • 除兩種輸出模式外,為防止高負載導至電壓下降,另有2.54mm接頭,直接籨 GPIO 供電,以減少電覽耗損及降壓。

《規格》

  • 尺寸:8.5cm x 5.5cm x 0.9cm
  • 重量:35g (不含電池重)

《商品清單》

  • 1 x 鋰電擴充板
  • 1 x 鋰電池(3.7V, 3800mAh)
  • 1 x 銅柱螺絲包
  • 1 x 排針

* 注意:本商品不包含 Raspberry Pi 主板。

$ 420



※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi PoE HAT (Power over Ethernet) 擴充板

Raspberry-Pi-PoE-HAT-4in1

The Raspberry Pi PoE HAT powers a Raspberry Pi 3 Model B+ via an Ethernet cable. Power-sourcing equipment is required on the Ethernet network.

《特色》

The Raspberry Pi Power over Ethernet HAT is a small accessory for the Raspberry Pi computer. It can only be used with the Raspberry Pi 3 Model B+ (launched March 2018). The PoE HAT allows you to power your Raspberry Pi using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed.

Supplied with this product

  • Raspberry Pi PoE HAT
  • Mechanical spacers

Other hardware needed

Connecting your PoE HAT to the Raspberry Pi

  • Before installing the PoE HAT, you must attach the supplied spacers in the four corners of the board
  • Then connect the Raspberry Pi PoE HAT to the two 0.1” headers (40 + 4) that are fitted on the Raspberry Pi
  • Once the PoE HAT board is connected, you can power the Raspberry Pi through its RJ45 network connector

Disconnecting your PoE HAT

  • Take care when separating the HAT from the Pi
  • Pull evenly so that it detaches from all the pins at the same rate; do not pull one end of the connector off before the other

Additional information

No modification to the main Raspberry Pi board is needed for this product to work. Please ensure that your Raspberry Pi’s software is up to date for all functionality to be available. The PoE HAT is fitted with a small fan that is controlled by the Raspberry Pi via I2C. The fan will turn on and off automatically depending on the temperature of the main processor on the Raspberry Pi.

《規格》

The Raspberry Pi PoE HAT is an add-on board for the Raspberry Pi 3 Model B+. It allows the Raspberry Pi to be powered via a power-enabled Ethernet network.

  • 802.3af PoE
  • Fully isolated switched-mode power supply
  • 37–57V DC, Class 2 device
  • 5V/2.5A DC output
  • 25mm x 25mm brushless fan for processor cooling
  • Fan control

《下載》

《安全提醒》

  • Shall only be powered using 802.3af-compliant power sourcing equipment; any external power supply used with the Raspberry Pi shall comply with relevant regulations and standards applicable in the country of intended use
  • Should be operated in a well-ventilated environment, and should not be covered
  • Should be placed on a stable, flat, non-conductive surface while in use, and should not be contacted by conductive items

Instructions for safe use

To avoid malfunction or damage to your Raspberry Pi product, please observe the following advice:

  • Do not block or obstruct the fan
  • Do not insert anything into the fan at any time
  • Do not expose the product to water or moisture, and do not place it on a conductive surface whilst it is in operation
  • Do not expose it to heat from any source; the product is designed for reliable operation at normal room temperatures
  • Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors
  • Avoid handling the Raspberry Pi while it is connected to a power outlet; only handle by the edges to minimize the risk of electrostatic discharge damage
  • All other peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met; these peripherals include, but are not limited to, keyboards, monitors, and mice used in conjunction with the Raspberry Pi

* 注意:本商品不包含 Raspberry Pi 3 Model B+。

$ 840



※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] PiJuice HAT – A Portable Power Platform For Every Raspberry Pi 樹莓派電源擴充板

PiJuice-HAT-4in1

 

As one of the smallest systems around there are so many amazing things you could do with the Raspberry Pi if it was self-powered and portable. Introducing PiJuice! A fully uninterruptible power supply that will always keep your Raspberry Pi powered.

Our revolutionary PiAnywhere technology contained in every PiJuice HAT – is the best way to take your Pi off the grid! The real time clock (RTC) on board will let your Pi know what time it is even with no power input or internet connection. Alongside this is an integrated microcontroller (MCU) chip which will manage soft shut down functionality and a true low power deep sleep state and intelligent startup.

You will be able to always keep track of the charge levels and other info with the two built-in tri-coloured RGB LEDs, trigger events and scripts with the three programmable buttons and since the PiJuice will use up to just five of your GPIO pins (just power and I2C), the rest are free to diversify your project. The stacking header allows you to continue to use your existing HATs and add-ons with PiJuice.

《特色》

  • Onboard 1820 mAh off the shelf Lipo / LiIon battery for ~4 to 6 hours in constant use! (with support for larger Lipo Battery of 5000 or 10,000 mAH+ to last up to 24 hrs +)
  • A Full Uninterrupted / Uninterruptable Power Supply solution.
  • Designed for the Raspberry Pi A+, B+, 2B, 3B and 3B+ but also compatible with Raspberry Pi Zero v1.3 and Raspberry Pi Zero Wireless.
  • Integrated Real Time Clock
  • Onboard intelligent on/off switch
  • Low power deep-sleep state with wake on interrupt/calendar event
  • Programmable multi-colored RGB led (x2) and buttons (x3) with super simple user-configurable options
  • Hardware watchdog timer to keep your Raspberry Pi on and working in mission-critical remote applications
  • Our revolutionary PiAnywhere technology ? the best way to take your Pi off the grid!
  • Full power management API available to Raspberry Pi OS with auto shutdown capability when running low on batteries
  • Raspberry Pi HAT compatible layout, with onboard EEPROM for easy plug and play operation
  • Low profile design to fit inside lots of existing Raspberry Pi cases!
  • Enhanced graphical user interface (GUI) available for easy install (via APT)
  • Customisable scripts for enhanced flexibility and full report of battery status
  • All GPIOs available via stackable header for ease of expandability and connectivity
  • Charge via on-board micro USB or via the Raspberry Pi micro USB (or from onboard pin headers)
  • Batteries can be charged from different type of sources and voltages
  • Replace the battery without downtime. Compatible with any single cell LiPo or LiIon battery
  • Fully CE and FCC tested design. Battery safety tested also.

 

《規格》

  • The EEPROM can be disabled and its I2C address changed for increased compatibility with other boards
  • BP7X battery – original battery from Motorola Droid 2 (A955) – 1820mAh battery
  • Microcontroller is an ST Micro STM32F030CCT6 ARM Cortex-M0, 48MHz, F64KB, R8KB, I2C, SPI, USART, 2.4-3.6V
  • Charge IC – BQ24160RGET Charger IC Lithium-Ion/Polymer, 2.5A, 4.2-10V
  • Fuel gauge IC – LC709203FQH-01TWG Battery Fuel Gauge, 1-Cell Li-ion, 2.8%
  • EEPROM – CAT24C32WI-GT3 EEPROM, I2C, 32KBIT, 400KHZ, 1V7-5V5
  • Optional spring pin – Mil-Max 0929-7-15-20-77-14-11-0
  • Compatible with any 4 pin battery on board that can be used with 00-9155-004-742-006 battery contacts from AVX including the BP7X, BP6X, and any compatible batteries including the 1600mAh and 2300mAh
  • ones from CameronSino (CS-MOA853SL and CS-MOA855XL)
  • There is an on board 4 pin screw terminal block for larger off board batteries. Any single cell LiPo / LiIon is compatible. However, you use your own sourced battery at your own risk. We HIGHLY RECOMMEND using
  • a battery with an internal protection circuit and a NTC (temp sensor)
  • Optional header for offboard button – connected to same output as SW1
  • 6 pin breakout header – with two GPIO from the ARM Cortex-M0, Vsys, 5v0, 3v3, GND connections
  • Header for optional off board solar panel / wind turbine etc.
  • Optional RF Shield attachment – Harwin S02-20150300 (can also double as an inexpensive heatsink)
  • Input voltage range – 4.2V 10V
  • Output voltage – 3.3V and 5V
  • Output amperage – maximum current at 5V gpio is 2.5A and at VSYS output 2.1A, but also this depends heavily on battery capacity. For BP7X have measured around 1.1A at 5V GPIO and around 1.6A at VSYS
  • output. Obviously, this also depends heavily on the current draw demanded by the Raspberry Pi/device itself. To achieve a maximum of 2.5A it will need battery over 3500mAh.
  • Boxed weight – 96g
  • Boxed dimensions – 12.2 x 10.8 x 3.5 cm
  • Unboxed weight – 57g
  • Unboxed dimensions – 6.5 x 5.6 x 2 cm

PiJuice HAT box contains

  • 1 x PiJuice HAT
  • 1 x Battery and battery surround
  • 1 x PiJuice guide
  • 4 x Mounting posts attached to PiJuice
  • 8 x Mounting screws (4 are already assembled to the board)
  • 1 x Pogo pin
  • 3 x Stickers

 

《下載》

《應用》

* 注意:本商品不包含 Raspberry Pi 主板。

$ 2450



※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] 散熱片風扇模組 (Raspberry Pi 3 Model B+ / Pi 3 Model B / Pi 2 / B+ 皆適用)

fan-heat-sink-4in1專為 Raspberry Pi 樹莓派設計的散熱片風扇模組,使用了風扇和散熱片結合而成,噪音低,壽命長,風量大,簡單而實用。附雙面膠可直接貼於晶片上,不需任何工具,也不受限於外殼款式,可置入大多數外殼內,適用於任一版本樹莓派或其他開發板上。

《特色》

* 適用於 Pi 3 B+ /  Pi 3 / Pi 2 / B+
* 散熱效率佳

《單風扇規格》

1 x 單風扇模組(25 x 25 x 16 mm)
1 x 銅散熱片(12 x 11 x 1 mm)
1 x 鋁散熱片(9 x 9 x 5 mm) 

《雙風扇規格》

1 x 雙風扇模組(56 x 25 x 13 mm)
1 x 銅散熱片(12 x 11 x 1 mm)
1 x 鋁散熱片(9 x 9 x 5 mm)


* 注意:本商品不包含 Raspberry Pi 主板。

$ 160 (單風扇模組)

$ 250 (雙風扇模組)



※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi 3 Model B+ 入門組
(含Pi 3B+主板 + microSD卡 + 5V/2.5A電源)

pi 3 B+ micro SD power supply

《規格》
1. Raspberry Pi 3 Model B+ x1
2. SanDisk microSD 記憶卡(32GB 或 64GB) x1
3. 5V/2.5A USB 電源轉換器 x1

$ 2,100 (Pi3B+ + 32G + 電源)

$ 2,415 (Pi3B+ + 64G + 電源)

※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi 3 Model B+ 入門升級組
(含Pi 3B+主板 + microSD卡 + 5V/2.5A電源 + 外殼)

pi 3 B+ microSD power supply official case

《規格》
1. Raspberry Pi 3 Model B+ x1
2. SanDisk microSD 記憶卡(32GB 或 64GB) x1
3. 5V/2.5A USB 電源轉換器 x1
4. Official 原廠紅白雙色外殼 x1

$ 2,400 (Pi3B+ + 32G + 電源 + 紅白外殼)

$ 2,715 (Pi3B+ + 64G + 電源 + 紅白外殼)

※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] 塑膠螺絲包 螺絲柱 (Raspberry Pi 3B+ / Pi 3 / Pi 2 / B+ 任意版本皆適用)

????????

由於Raspberry Pi 樹莓派 開發板的固定孔大小較特殊,一般的螺絲無法用來固定,硬鎖上去便可能會傷到主板,因此需要特製規格才能正常使用,專為 Raspberry Pi 樹莓派設計的塑膠螺絲/螺絲柱,適用於任一版本樹莓派或Arduino、BeagleBone等絕大多數開發板上。

《特色》
* 適用於 Pi 3 B+ /  Pi 3 / Pi 2 / B+ 等任意版本。
* 適用於 Arduino / BeagleBbone及絕大多數開發板。

《規格》
本商品包含:
* 塑膠螺絲 x16
* 塑膠螺絲柱 x16
* 塑螺帽 x16

$ 100


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi(未銲) 伺服馬達擴充板

Adafruit-16-Channel-PWM-Servo-HAT-for-Raspberry-Pi-Mini-Kit

 

The Raspberry Pi is a wonderful little computer, but one thing it isn’t very good at is controlling DC Servo Motors – these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running.

《規格》
- Raspberry Pi Model A+, B+, or Pi 2 適用
- Servo HAT x1
- 2-pin terminal block x1
- 3×4 headers x4
- 2×20 socket header x1

* 注意:本產品不含Raspberry Pi及伺服馬達。

$ 700


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Adafruit DC & Stepper Motor HAT for Raspberry Pi – Mini Kit(未銲) 直流 & 伺服馬達擴充板

Adafruit-DC-Stepper-Motor-HAT-for-Raspberry-Pi-Mini-Kit-4in1

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control.

《規格》
- 65mm x 56mm x 13mm / 2.6″ x 2.2″ x 0.5″
- Raspberry Pi Model A+, B+, Pi 2, Pi 3, Pi 3 Model B+皆適用
- Servo HAT x1
- 2-pin terminal block x3
- 3-pin terminal block x2
- 2×20 socket header x1

* 注意:本產品不含Raspberry Pi及馬達。

《教學》
Adafruit DC and Stepper Motor HAT for Raspberry Pi
Simple Raspberry Pi Robot

《下載》
Datasheets, schematic, PCB files, and Fritzing available in the product tutorial

$ 900


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Adafruit PiTFT Plus 320×240 2.8″ TFT + Capacitive Touchscreen (Raspberry Pi 樹莓派 2.8 吋電容式觸控螢幕)

PiTFT-Plus-320x240-2.8inch-Capacitive-Touchscreen-s

《特色》
* 具有2.8″ 顯示屏、320×240 解析度@16-bit per pixel
* 電容式觸控螢幕,使用更靈敏
* 適用於 Raspberry Pi 3 / Pi 2 / B+ / Model A+ / Zero / Zero W 等,含 2×20 腳位的任何 Pi
* 另有拉出所有40Pin GPIO 腳位,可供使用
* 使用I2C pins(SDA & SCL)、SPI pins(SCK, MOSI, MISO, CE0) 和 GPIO #25、#24,其餘 GPIO 未使用

PiTFT-Plus-320x240-2.8inch-Capacitive-Touchscreen-4in1

《規格》
* 本套件的腳位連接埠已經焊接好,不需再自行焊接
* 本套件包含觸控螢幕面板與底板,不包含其他組件
* 螢幕尺寸:50mm x 69mm x 4mm / 2″ x 2.7″ x 0.16″
* PCB尺寸:56mm x 85mm x 11mm / 2.2″ x 3.3″ x 0.4″
* 重量:47g

* 注意:本擴充板不包含 Raspberry Pi!

《教學》
* Adafruit 2.8″ PiTFT – Capacitive Touch
* DIY WiFi Raspberry Pi Touchscreen Camera

《相關》
- [產品] PiTFT Plus 480×320 3.5″ TFT+Touchscreen for Raspberry Pi 3/Pi 2/A+/B+
- [產品] PiTFT Mini Kit – 320×240 2.8″ TFT+Touchscreen for Pi
- [產品] PiTFT Mini Kit – 320×240 2.8″ TFT+ Capacitive Touchscreen

《下載》
* The latest kernel fork that adds all the TFT, touchscreen, and other addons is here on github
* Datasheet for the ‘raw’ 2.8″ TFT display
* FT6206 Datasheet & App note (capacitive chip)
* EagleCAD PCB files on GitHub

$1780 


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] 銅製散熱片(Raspberry Pi 3B+ / Pi 3 / Pi 2 / B+ 適用)

copper-heat-sink-s

《特色》
* 適用於 Pi 3 B+ /  Pi 3 / Pi 2 / B+
* 本商品包含:銅製散熱片 x2 + 薄型銅片 x1

copper-heat-sink-pi3-s

《規格》
散熱片尺寸:12 x 13 x 5.3 mm
銅片尺寸:15 x 15 x 1.2 mm
* 注意:本商品不包含 Raspberry Pi 主板。

$ 100



※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。