[活動] Raspberry Pi社群聚會 #25 @2019/04/29


RSVP:Raspberry Pi Meetup #25
The 25th of the Raspberry Pi meetup, the topic is “Raspberry Pi HAT”.

Speaker 1:Larry (Joybien Technologies))
Topic:5G mmWave IoT Sensor Introduction & Application
1) mmWave Technology Introduction
2) Joybien mmWave Solution Platform
3) mmWave Sensor Application: Vital Signs Detection (VSD)
4) mmWave Sensor Application: People Movement Behavior (PMB)
5) mmWave Sensor Application: High Accuracy Measurement (HAM)
6) DEMO: VSD & PMB & HAM with Raspberry Pi Interaction

Speaker 2: sosorry
Topic: The introduction of Raspberry Pi TV HAT and NanoSound DAC

Lightning Talk: Jack (Sivann)
Topic: TestMate circuit testing good partner
1) Introduction to TestMate
2) Application of RPi and TestMate

Additional Information:

  • 2019/04/29 19:10 ~ 21:30
  • 2F., No.105, Sec. 1, Chongqing S. Rd., Zhongzheng Dist., Taipei City
  • $150 per person

* Safeguarding

- – – – – – – – – - 以下為中文 – – – – – – – – – -

報名:Raspberry Pi社群聚會 #25

第二十五次 Raspberry Pi 社群聚會,希望能透過社群活動的分享和交流,找到更多 Raspberry Pi 的可能。本次主題是「樹莓派擴充板(HAT)應用」。

分享者1:Larry (玖邦科技))
題目:5G 毫米波物聯網感測應用介紹
1) 毫米波技術介紹
2) 玖邦科技 毫米波方案平台
3) 毫米波感測應用: 生命跡象偵測 (VSD)
4) 毫米波感測應用: 人員動態行為 (PMB)
5) 毫米波感測應用: 高精度量測 (HAM)
6) DEMO: 與樹莓派互動的生命跡象偵測 (VSD) & 人員動態行為 (PMB) & 高精度量測 (HAM)

題目:樹莓派電視擴充板(TV HAT)和 NanoSound

閃點講:Jack (愛文西門科技)
題目:TestMate 測試電路的好夥伴
1) TestMate 介紹
2) RPi 與 TestMate 的小應用


  • 活動時間: 2019/04/29(週一) 19:10 ~ 21:30 (6:40pm 開始入場)
  • 活動人數上限: 100
  • 活動地點:台北市重慶南路一段105號2樓(天瓏書局)


  • 每人150元場地費用
  • 帶作品展示的參加者免收場地費用


  • 活動場地有提供無線網路

* 安全措施

報名:Raspberry Pi社群聚會 #25

[產品] Raspberry Pi 樹莓派 UPS 鋰電池擴充板 USB 電源供應模組 行動電源 雙USB輸出


專為樹莓派設計的 UPS 鋰電池擴充板,雙USB輸出,可當行動電源使用,或用於其他USB供電等設備。


  • 適用於B+以後版本樹莓派,Raspberry Pi A+B+2B3B and 3B+
  • 可邊充邊放,停止充電時不影響放電
  • 雙模供電:行動電源模式及UPS供電模式
    • 行動電源模式,採鋰電池供電,最高可達 5.1V/2.5A。
    • UPS供電模式,microUSB input 接上5V/2A電源,output 最高可達 5.1A/3A
  • 4+2LED 顯示充電、放電及電池狀態
  • 保護功能:output 有一個self-recovery fuse保險絲,防止樹莓派因外部短路而燒毀
  • 除兩種輸出模式外,為防止高負載導至電壓下降,另有2.54mm接頭,直接籨 GPIO 供電,以減少電覽耗損及降壓。


  • 尺寸:8.5cm x 5.5cm x 0.9cm
  • 重量:35g (不含電池重)


  • 1 x 鋰電擴充板
  • 1 x 鋰電池(3.7V, 3800mAh)
  • 1 x 銅柱螺絲包
  • 1 x 排針

* 注意:本商品不包含 Raspberry Pi 主板。

$ 420

※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi TV HAT 擴充板



This add-on board lets you receive digital DVB-T2 TV streams on your Raspberry Pi to view them or stream them over a network to other devices.



  • Any 40-pin Raspberry Pi (including Pi Zero and Zero W, provided they have headers soldered)
    • Any Raspberry Pi can be used to stream to other devices
    • A Raspberry Pi 2 or 3 (or later) is recommended for viewing TV on the Pi itself
  • A suitable aerial to receive broadcast TV (not provided)

We’ve put together a downloadable step-by-step guide to Getting started with the TV HAT, which walks you through the complete setup process.


The Raspberry Pi TV HAT has a DVB-T2 and DVB-T tuner on board, which allows you to receive and decode digital television streams on your Raspberry Pi.

  • Sony CXD2880 TV tuner
  • Supported TV standards:
    • DVB-T2 (1.7MHz, 5MHz, 6MHz, 7MHz, 8MHz channel bandwidth)
    • DVB-T (5MHz, 6MHz, 7MHz, 8MHz channel bandwidth)
  • Reception frequency: VHF III, UHF IV, UHF V



More detailed information on Raspberry Pi hardware is available.


The Raspberry Pi TV HAT will remain in production until at least January 2023.




Raspbian Stretch (or later) is required for using the TV HAT. Download the latest version of Raspbian here.

For how to install Raspbian, see our online guide to Getting started with your Pi.


The software we recommend for decoding TV streams and viewing content is TVHeadend. Instructions for setting this up are in our  guide to Getting started with the TV HAT.


  • Kodi
  • OMXplayer
  • LibreELEC

* 注意:本商品不包含 Raspberry Pi 主板。

$ 945 

※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] Raspberry Pi PoE HAT (Power over Ethernet) 擴充板


The Raspberry Pi PoE HAT powers a Raspberry Pi 3 Model B+ via an Ethernet cable. Power-sourcing equipment is required on the Ethernet network.


The Raspberry Pi Power over Ethernet HAT is a small accessory for the Raspberry Pi computer. It can only be used with the Raspberry Pi 3 Model B+ (launched March 2018). The PoE HAT allows you to power your Raspberry Pi using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed.

Supplied with this product

  • Raspberry Pi PoE HAT
  • Mechanical spacers

Other hardware needed

Connecting your PoE HAT to the Raspberry Pi

  • Before installing the PoE HAT, you must attach the supplied spacers in the four corners of the board
  • Then connect the Raspberry Pi PoE HAT to the two 0.1” headers (40 + 4) that are fitted on the Raspberry Pi
  • Once the PoE HAT board is connected, you can power the Raspberry Pi through its RJ45 network connector

Disconnecting your PoE HAT

  • Take care when separating the HAT from the Pi
  • Pull evenly so that it detaches from all the pins at the same rate; do not pull one end of the connector off before the other

Additional information

No modification to the main Raspberry Pi board is needed for this product to work. Please ensure that your Raspberry Pi’s software is up to date for all functionality to be available. The PoE HAT is fitted with a small fan that is controlled by the Raspberry Pi via I2C. The fan will turn on and off automatically depending on the temperature of the main processor on the Raspberry Pi.


The Raspberry Pi PoE HAT is an add-on board for the Raspberry Pi 3 Model B+. It allows the Raspberry Pi to be powered via a power-enabled Ethernet network.

  • 802.3af PoE
  • Fully isolated switched-mode power supply
  • 37–57V DC, Class 2 device
  • 5V/2.5A DC output
  • 25mm x 25mm brushless fan for processor cooling
  • Fan control



  • Shall only be powered using 802.3af-compliant power sourcing equipment; any external power supply used with the Raspberry Pi shall comply with relevant regulations and standards applicable in the country of intended use
  • Should be operated in a well-ventilated environment, and should not be covered
  • Should be placed on a stable, flat, non-conductive surface while in use, and should not be contacted by conductive items

Instructions for safe use

To avoid malfunction or damage to your Raspberry Pi product, please observe the following advice:

  • Do not block or obstruct the fan
  • Do not insert anything into the fan at any time
  • Do not expose the product to water or moisture, and do not place it on a conductive surface whilst it is in operation
  • Do not expose it to heat from any source; the product is designed for reliable operation at normal room temperatures
  • Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors
  • Avoid handling the Raspberry Pi while it is connected to a power outlet; only handle by the edges to minimize the risk of electrostatic discharge damage
  • All other peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met; these peripherals include, but are not limited to, keyboards, monitors, and mice used in conjunction with the Raspberry Pi

* 注意:本商品不包含 Raspberry Pi 3 Model B+。

$ 840 (單買 PoE HAT)

若需使用GPIO可加購 PoE HAT 專用長排針組 3 Model B+。
PoE HAT Stacking Header

$ 960 (PoE HAT 加長排針)

※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] 智慧喇叭語音學習套件


1. 手把手教學,附完整範例程式,可結合智慧插座套件做語音控制開關。
2. 可使用 NLTK結巴(Jieba)做中英文斷詞和自然語言處理。
3. 可嵌入 Google Assistant 或是雲端語音辨識功能,例如 AlexaOlami 等。
4. 可串接 snowboy 自訂喚醒詞,串接 Dialogflow 自然語言理解平台。
5. 全系列 Pi 都可以使用。

1. ReSpeaker雙麥克風擴充板(2-Mics Pi HAT)
2. Grove 母排線 x1
3. Grove 公排線 x1
4. 高品質攜帶式喇叭(USB 充電)
5. 萬用電子零件包

* [Wiki]ReSpeaker 2-Mics Pi HAT
* 1.Get started with Google Assistant
* 2.How to use button to trigger Google Assistant


改造 ReSpeaker 2-MIC HAT from raspberrypi-tw

* 改造 ReSpeaker 2-MIC HAT

* https://github.com/raspberrypi-tw/hack-respeaker


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。

[產品] ReSpeaker雙麥克風擴充板(2-Mics Pi HAT)


ReSpeaker 2-Mics Pi HAT 是一個適用於語音應用的雙麥克風擴充板。該擴充板使用 WM8960 的低功耗立體聲編解碼器,兩側有兩個麥克風可收音,讓您可以很容易的串接 Amazon Alexa Voice Service 或是 Google Assistant 等語音服務。此外,擴充板上還有 3 個 APA102 RGB LED,1 個按鍵和 2 個 Grove 介面,讓您很容易擴充其他硬體與應用程式。板上的 3.5mm 音訊插孔或 JST 2.0 揚聲器輸出均可用於音訊輸出。


* Raspberry Pi Zero / Zero W / B+ / Pi 2 / Pi 3 適用
* 雙麥克風
* 2 個 Grove 介面: 支援 GPIO 及 I2C
* 可程式化控制按鍵及 LED 燈(包括 1 按鍵和 3 LED 燈)
* 內鍵音訊編/解碼器
* 雙音訊輸出: 3.5mm 音訊插孔、JST2.0 揚聲器輸出
* 可遠至 3 公尺外收音
* 尺寸: 65mm x 30mm x 15mm
* 重量:G.W 34g N.W 12g

* 注意:本擴充板不包含 microSD卡 及 Pi Zero!

* [Wiki]ReSpeaker 2-Mics Pi HAT
* 1.Get started with Google Assistant
* 2.How to use button to trigger Google Assistant
* 改造 ReSpeaker 2-MIC HAT 教學投影片

* 改造 ReSpeaker 2-MIC HAT

* https://github.com/raspberrypi-tw/hack-respeaker

* [新聞] Raspberry Pi Zero 套餐特價中
* [產品] Raspberry Pi Zero v1.3 + Mini HDMI轉接頭 + OTG + 8G microSD + 5V電源 + 2×20排針
* [產品] Raspberry Pi Zero v1.3 + Raspberry Pi Camera(v2)
* [產品] Raspberry Pi Zero v1.3 + Raspberry Pi NoIR Camera(v2)


※若無法使用Paypal購買,請到 這裡 填寫表單購買,造成您的不便敬請見諒。