The Raspberry Pi PoE HAT powers a Raspberry Pi 3 Model B+ via an Ethernet cable. Power-sourcing equipment is required on the Ethernet network.
The Raspberry Pi Power over Ethernet HAT is a small accessory for the Raspberry Pi computer. It can only be used with the Raspberry Pi 3 Model B+ (launched March 2018). The PoE HAT allows you to power your Raspberry Pi using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed.
Power-sourcing equipment for a 802.3af Power over Ethernet network
Connecting your PoE HAT to the Raspberry Pi
Before installing the PoE HAT, you must attach the supplied spacers in the four corners of the board
Then connect the Raspberry Pi PoE HAT to the two 0.1” headers (40 + 4) that are fitted on the Raspberry Pi
Once the PoE HAT board is connected, you can power the Raspberry Pi through its RJ45 network connector
Disconnecting your PoE HAT
Take care when separating the HAT from the Pi
Pull evenly so that it detaches from all the pins at the same rate; do not pull one end of the connector off before the other
No modification to the main Raspberry Pi board is needed for this product to work. Please ensure that your Raspberry Pi’s software is up to date for all functionality to be available. The PoE HAT is fitted with a small fan that is controlled by the Raspberry Pi via I2C. The fan will turn on and off automatically depending on the temperature of the main processor on the Raspberry Pi.
The Raspberry Pi PoE HAT is an add-on board for the Raspberry Pi 3 Model B+. It allows the Raspberry Pi to be powered via a power-enabled Ethernet network.
Shall only be powered using 802.3af-compliant power sourcing equipment; any external power supply used with the Raspberry Pi shall comply with relevant regulations and standards applicable in the country of intended use
Should be operated in a well-ventilated environment, and should not be covered
Should be placed on a stable, flat, non-conductive surface while in use, and should not be contacted by conductive items
Instructions for safe use
To avoid malfunction or damage to your Raspberry Pi product, please observe the following advice:
Do not block or obstruct the fan
Do not insert anything into the fan at any time
Do not expose the product to water or moisture, and do not place it on a conductive surface whilst it is in operation
Do not expose it to heat from any source; the product is designed for reliable operation at normal room temperatures
Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors
Avoid handling the Raspberry Pi while it is connected to a power outlet; only handle by the edges to minimize the risk of electrostatic discharge damage
All other peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met; these peripherals include, but are not limited to, keyboards, monitors, and mice used in conjunction with the Raspberry Pi
誰在 Facebook 發訊息給你？ 有新的 Twiiter 到了嗎？Scroll Bot 套件包含一個 Pi Zero W，一個 17×7 像素的 LED 矩陣擴充板(Scroll pHAT HD)，還有超可愛的外殼和所有您會需要的零件。
* Pi Zero W * Scroll pHAT HD with 17×7 individually dimmable white LEDs
* Male and female 2×20 pin headers
* Orange robot stand and diffuser
* 50cm USB A to micro-B cable
* USB A (female) to micro B (male) adaptor
* Mini to full-size HDMI adaptor
* Sticker sheet (personalize your Scroll Bot!)
* Comes in a reusable kit box
* Assembled size of Scroll Bot is 125x85x67mm (WxHxD)
The 20th of the Raspberry Pi meetup, the topic is “Voice Control and Applications”.
Speaker 1：Zoe Chen(YPCloud), Steve Hu(LILIN)
Topic: Raspberry Pi control NVR with YPCloud + MQTT + Alexa
Speaker 2：Ryan Hang (OLAMI Open AI – VIA Technologies, Inc)
Topic: Build your own smart speaker with Raspberry Pi + OLAMI AI platform
1. Introduction to OLAMI Open cloud-based AI platform.
2. Build your own smart speaker with Raspberry Pi + OLAMI AI platform.
3. DIY and Demo.
2017/09/26(Tuesday) 19:10 ~ 2017/09/26 21:30
4F-1., No.293, Sec. 1, Fuxing S. Rd., Da’an Dist., Taipei City 106
The Raspberry Pi is a wonderful little computer, but one thing it isn’t very good at is controlling DC Servo Motors – these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running.
- Raspberry Pi Model A+, B+, or Pi 2 適用
- Servo HAT x1
- 2-pin terminal block x1
- 3×4 headers x4
- 2×20 socket header x1
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control.
- 65mm x 56mm x 13mm / 2.6″ x 2.2″ x 0.5″
- Raspberry Pi Model A+, B+, Pi 2, Pi 3, Pi 3 Model B+皆適用
- Servo HAT x1
- 2-pin terminal block x3
- 3-pin terminal block x2
- 2×20 socket header x1
* 10Mbps 乙太網路連線
* 雙 LED 燈顯示連線狀態
* HAT-standard-compliant EEPROM makes setup automatic, works straight away with Raspbian!
* 使用 Zero 的 GPIO 腳位，不佔用 USB 孔！
* 長 x 寬 x 高：65.5mm x 32.3mm x 23.0mm / 2.6″ x 1.3″ x 0.9″
* 重量：15.6g / 0.6oz