* Integrated PLL; Transmitter; Receiver; Baseband; and A2D * 76- to 81-GHz Coverage With 4-GHz Continuous Bandwidth * Four Receive Channels * Two Transmit Channels * Ultra-Accurate Chirp (Timing) Engine Based on Fractional-N PLL * TX Power: 12.5 dBm * RX Noise Figure: 14 dB (76 to 77 GHz)/15 dB (77 to 81 GHz)
Built-in Calibration and Self-Test (Monitoring)
* ARM® Cortex® -R4F-Based Radio Control System * Built-in Firmware (ROM) * Self-calibrating System Across Frequency and Temperature
DSP
C674x DSP for FMCW Signal Processing
MCU
* ARM Cortex-R4F Microcontroller for Application Control * I/O; SPI / CAN x 1 * Up to 2 UARTs I2C x 1 * GPIO: 0 ~ 2
Pre-Programmed Firmware "Flavor"
* Vital Signs Detection (VSD) Firmware; for 30cm ~ 90cm wireless & contactless detection of Heartbeat & Respiration Rate * High Accuracy Measurement (HAM) Firmware; for 30cm ~ 300cm distance measurement with millimeter resolution * People Movement Behavior (PMB) Firmware; for detecting People Movement in 4m x 4m or 16 meter-square region for setting geo-fence(s) trigger action * Note: ONLY one of VSD; HAM; or PMB Firmware is pre-programmed within a single mmWave Module
Operating Temperature
0° to 40° degree Celsius
Operating Humidity
10 ~ 85% Non-Condensing
Dimensions & Weight
54.1mm x 45.7mm; 13.7 grams net
《出貨清單》
* mmWave 雷達 x1
* Raspberry Pi BLE HAT 擴充板 x1
* 塑膠螺絲柱 x8
The RN2483 LoRa® Mote is a LoRaWAN™ Class A end-device based on the RN2483 LoRa modem. As a standalone battery-powered node, the Mote provides a convenient platform to quickly demonstrate the long-range capabilities of the modem, as well as to verify inter-operability when connecting to LoRaWAN v1.0 compliant gateways and infrastructure.
The Mote includes light and temperature sensors to generate data, which are transmitted either on a fixed schedule or initiated by a button-press. An LCD display provides feedback on connection status, sensor values and downlink data or acknowledgements. A standard USB interface is provided for connection to a host computer, providing a bridge to the UART interface of the RN2483 modem. As with all Microchip RN family of products, this enables rapid setup and control of the on-board LoRaWAN protocol stack using the high level ASCII command set.
《特色》 * 868 MHz High-Frequency SMA Connector
* 433 MHz Low-Frequency Antenna test Point
* USB Mini-B Connector
* PIC18LF45K50 8-bit MCU
* Mote ICSP Programming
* LCD Display
* S1 & S2 Switches (for Menu Navigation)
* Ambient Light Sensor
* Linear Active Thermistor (MCP9700T)
* LDO Regulator (MCP1825S)
* Descriptive LEDs, (2) Controlled by PIC18, (2) Controlled by Module * (2) AAA Battery Pack
* Battery Power Switch
* Alternative Power Supply Through Hole Connectors
《規格》
* Manufacturer: Microchip * Frequency: 433 MHz, 868 MHz/915 MHz * Output Power: 14dBm
* Operating Temperature Range: -40ºC to 85ºC
* Input Sensitivity -148mVpp
* Rx Input Sensitivity -148dB
* TX Current Consumption: 40mA (14dBm, 868MHz)
* RX Current Consumption: 14.2mA
* Interface Type: UART
* Unit Weight: 221.400 g
《套件內容》 * RN2483 LoRa® Technology Mote
* SMA Antenna
* USB (standard-A to mini-B) cable
* Info Sheet DS50002391
* Pack Lis